Reference for the syringe. Now mine isn't 100% exact but as it's stated in the game, the needles are all put together with spare parts. So some may vary from others.
Here's how we start our journey! The first thing you want to start off with is a gas pump. Can't really do anything unless you want to guess the sizes of the PVC pipe you're going to use on it and guess the other parts. You'll want a gas pump from the 1930's and you can find them on Ebay. It make take some time to find a cheap one. The cheapest I found was about $23. So just be patient and keep looking until you find a nice cheap pump. That aside, once you have your pump you can begin working. I'll use the needle I made as an example. Most of the measurements as far as circumference goes for most things, should work.
The PVC pipe is colored blue. The wooden dowel is red and the Bondo, or some other putty that hardens like cement, is green. You'll want to get a PVC pipe with a 1 1/2 inch diameter and make it just a little over 6 inches long. The wooden dowel should be 1/4 inch in diameter and be 19 inches long. The PVC needs to be filled with the bondo automobile body filler (or other putty) 3 inches thick. You can either stick the dowel in now and center it or you can wait until it dries and drill a hole then insert it. When the dowel is inserted it must go down 3 inches into the bondo. If you chose to drill a hole and insert it, make sure to use epoxy and pour some into the hole before inserting the dowel to secure it. Sand the dowel at a gradual decline to make the needle and you should have the bottom image or similar. You will also need to sand the end of the PVC end about 1/2 inch in to insert it into the gas pump. Secure it with epoxy as well.
The next part is the jar, or the "Adam" vile, that goes on top of the gas pump. For this you're going to need two mason jar lids. Start with the bottom one that attaches to the gas pump. For this one you will need Bondo again (or some other filler putty, something durable!). Take this piece and fill it in where the green area is on the image below. After it dries make sure to sand it down smooth and flat. You will also need a 1/4 inch diameter and 1 1/2 inch long metal tube. Drill a centered hole in the top of the gas pump and the bondo and insert the metal tube fixing it in place with epoxy. Also make sure at least 4/6 ths of the tube is showing.
Then comes the jar. Several images below show how it should look. Take an empty clean peanut butter jar (you'll need to test a few) and fit it into the other rim. If it locks on you're golden. Then find a clear bottom end of a small cup or a plastic bottle (I used a small bottle for mine). This would be the red part. If you want your gun to glow then you should definitely add this part. Check and see if the bottle end fits up into the rim. If it fits in with the jar then it's perfect. Now take them all out with the rim alone. You're going to need a waterproof glue for this since it's going to contain liquid or red color dyed water. I recommend using Amazing GOOP Marine. It's meant specifically for anything underwater as the title states. Place goop on the outside of the bottle end and also all around the inside of the rim. Insert the bottle end and then screw on the peanut butter jar. DO NOT turn upside down or the glue will get all over the inside. Cut a small hole in the top with a razor to allow the glue to air-out and dry faster.
This is an example of what happens when you try to speed up the glue drying. This was my first jar that got warped after I tried to speed things along. If you're going to try and use heat to dry the glue faster, please be very careful.
The second bottle. Better than the first and also better sealed with the marine Goop. I'm actually glad I messed up on the first one.
Later on you'll be able to cap it with a baby bottle nipple. Now allow the glue to dry for a couple days. Do not glue the jar to the other rim yet if you want to add a light to it. I will add a section later on for the light for whoever wants to know how to do it. Next is the baby bottle nipple. This will be glued to the top of the jar once it's filled and re-capped. To make this all you need is a baby bottle nipple and a small door nob cover. You may have to drill a hole to widen the hole and insert the nipple. Once it's inserted, epoxy it in place.
At this point it should look something like this.
From here on I'll be adding extra details because as you can see mine is still not finished. Some repairs need to be made and the light still needs to be installed. If you want to get a jump start on coloring use a Hammered texture bronze and silver spray paint. They work the best for a more worn and weathered look. If you want to really weather it get creative. Use dirt, sand, scratch it, use a light touch of black acrylic paint, whatever you can think of to make it look like it's been used and eroded.
Update 1: Disaster! During my travel when I was transporting the needle the syringe snapped. All I could think was " Bummer... " but it's really no big deal. If you find yourself in this situation don't panic. Just use wood glue to mend it and if it's missing some chips, fill it in with bondo and sand it down to it's original shape.
I took a picture of the items I used to make the light and also the items I needed to finish what was left of the needle. I'll take another picture and replace the one I have here since it's not the best quality picture. At the top is a Epoxy Glue (waterproof) to mend the top of the bottle I cut open. To the left is a Solder gun and electric tape. At the very center is solder (or lead. Careful, fumes are potent. Try not to breathe in.) Below the solder is a 1 dollar book light. I cut the wire between the light and the on-and-off switch, exposed the wires, then took a positive and negative wire to extend it's reach to run up through the gun.Finally, to the right is Flux! Not required...but it's helpful when soldering the wires together. You can find this stuff at any hardware store. Luckily for me my father was an electrician at one point and now he makes stained glass lamps in his spare time so all of this stuff was available to me. Most of these items are relatively cheap except for the solder gun. Ask family members or friends if the have these items just to save some cash.
Here is a very bad example of how the wires are soldered together. I'll draw an image up to replace this since I already soldered my light together. I soldered the extension wires to the on-and-off switch first and ran the wires through to the top/ Then I soldered the wires to the light. I screwed the top back in and stuffed the light down into place and it worked just dandy.
Finishing the disaster I had earlier with the bottle.I waited a VERY long time to wait for the Goop Glue to dry completely. On the previous bottle I didn't allow the glue to dry for a few day so when I added the water it eventually gooped up and made water milky and it also leaked. I tested it a few times during the day just to make sure the glue held well enough. It did. Then I filled it up and added color dye. Several drops of red dye, 3 drops of yellow, and I dabbed the end of a tooth pick in blue dye and touched the water with it a couple times to darken the red slightly. The first image below is very diluted because I only added 2 drops of red food dye. The image after is what the water should look like. If it's too dark some of the water can be poured out and a little more can be added to dilute it slightly. After I had a color that looked close enough to bloody goodness I epoxied the top of the back on. This is Very Important! I mixed up a small batch of epoxy and waited for it to harden slightly. Test it by taking a tooth pick and pulling some onto the end. Watch it. If the glue runs then don't put it on yet. If it doesn't run or it runs slightly then it's ok to put on. I got the 30 minute epoxy and waited about 15 minutes before putting it on the bottle. I taped the cap of the bottle to my finger and held it in place for 20 minutes to make sure it glue properly. (watching glue dry will be the most exciting experience of your life!) Once it finished gluing, I took a little more glue and epoxied what I missed under my finger and added a little more all around just to make sure the cap was completely sealed. The bottle will sit for a couple days to let the epoxy completely dry and then I'll finish it by epoxying the nipple to the top of the bottle and then gluing the bottle to the gun.
No comments:
Post a Comment